Professional club / DJ mixer Voted Best Club Installation Mixer in the DJ Magazine Techno-Scan Awards 2002 & 2003

This purebred club mixer has truly raised the bar in terms of club audio quality. It’s also quickly become the mixer of choice for many of the world’s greatest DJs, thanks to its pristine sound, its phenomenal VCF filters and its creative 4 band EQ. Club owners – if you want to know how good your big-money speaker system could sound, try it with a Xone:62.

The Xone:62 ships with mains leads, user guide, A&H stickers

6 Dual Stereo Channels
CH 1&2 have XLR Mic inputs and [TRS] stereo line level inputs, with ‘corrective’ EQ. CH 3-6 have stereo RCA RIAA turntable inputs and stereo RCA line level inputs, plus powerful 4 band ‘music’ EQ. All channels have 3 colour bar meter and gain control, EQ on switch and 60mm fader. CH 3-6 have X-fade assign section

Stereo Mix Outputs
Balanced mix outputs on XLR with level control, plus secondary RCA ‘music only’ outputs for recording. A post fade [TRS] mono sum output is also provided. The mix signal is displayed on 12 segment 3 colour bar meters

Auxiliary Send
All channels have a stereo auxiliary send which can be individually switched pre or post fade. There is also a post crossfader send to this stereo aux, so a program feed to a zone is possible. The outputs are [TRS] jacks

4 Band EQ
Powerful 4 band EQ with ‘asymmetric’ characteristic on CH 3-6; +6dB boost to preserve headroom and -26dB cut for creative mixing. CH 1&2 have ‘corrective’ EQ for mic & line control. EQ on switches are provided

VCA Cross Fader
Conductive plastic, high quality 45mm Penny & Giles fader with curve switchable to cut or dip. Channels 3-6 can be assigned to X left side or Y right side, with green / yellow led indication. The fader is a VCA design, so wear and tear does not affect audio. Drop-in replacements. Pan trim control for imbalance

Voltage Controlled Filters
2 filters [1 for each side of the x-fader] with choice of High Pass, Band Pass, Low Pass or multiples e.g. notch. Resonance - adjusts Q from ‘mild to wild’. Sweep controls from 100Hz to 20kHz with blue led on switch

Engineer / DJ’s Toolbox
High powered headphone output with level. ‘Music only’ Booth output on [TRS] jacks with level. 12 segment 3 colour bar metering displays mix or cue/monitor section. Channel cue overrides the monitor selected in the phones [option for post-EQ on CH 3-6]. Split Cue sends cue signals to left and selected program to right. Mute kills booth monitor output. Booth Mono sum button for phase and compatibility check

PSU
High performance internal switched-mode power supply. Universal mains input voltage

Configuration options
Internal links: individual channel aux sends to pre-EQ and CH 3-6 cue to post-EQ. 9 pin user connector (D-type female) for custom modifications and remotes (require competent installation or service personnel)

Connections

INPUTS
CH 1-2 IN (Mic)	Balance XLR female	2k ohm	-45 to -15dBu
(Stereo Line)	Unbalanced TRS jack	>10 ohm	-15 to +15dBu
CH 3,4,5,6 (Phono)	RCA phono RIAA	47k ohm/330pF2 to 100mV
(Stereo Line)	RCA phono	>10 ohm	>10k to +10dBu
OUTPUTS
MIX OUT L,R (XLR)	Balanced XLR male	<75 ohm	+4dBu
RECORD OUT	RCA Phono	<600 ohm	-10dBV
MONO OUT	Impedance balance TRS jack	<600 ohm	-2dBu
AUX OUT L,R	Impedance balance TRS jack	<75 ohm	-2dBu
BOOTH OUT	Impedance balance TRS jack	<75 ohm	-2dBu
HEADPHONES	Tip = L Ring = R 30 to 600 ohm recommended

 

 

 

Specifications

 

0dBu = 0.775 Volts rms, +4dBu = 1.23V rms 0dBV = 1 Volt rms, -10dBV = 316mV rms

Max output level XLR +26dBu into >2k ohm

TRS +21dBu into >2k ohm

RCA +15dBu into >10k ohm

Headroom Channels +21dB

Mix to output +23dB

Freq response +0/-1dB 20Hz to 40kHz

Distortion < 0.006% THD+noise @1kHz

Crosstalk < 90dB Channel shutoff @1kHz

MIC EIN 22-22kHz -128dB 150 ohm source

Residual noise XLR -90dBu (-94dB S/N)

TRS -84dBu (-84dB S/N)

RCA -92dBu (-84dB S/N)

Mix noise XLR -86dBu (-90dB S/N)

TRS -83dBu (-83dB S/N)

RCA -91dBu (-83dB S/N)

 

Power Supply

Internal switch mode power unit with auto sensing mains input.

MAINS IN socket IEC 3 pin

Power lead Country dependent with moulded mains plug supplied

AC mains 100 to 240V AC @ 50/60Hz

Consumption 30W max

Mains fuse rating 100-240V AC T500mA 20mm

Dimensions and Weights

The console is fitted with rubber feet for desktop operation. An optional screw on rack ear kit is

available for rack or plinth mounting.

Width Height Depth Weight

Desktop 320 mm (12.6”) 105 mm (4.1”) 358 mm (14.1”) 5 kg (11 lbs)

Rack ears fitted 370 mm (14.6”) 105 mm (4.1”) 358 mm (14.1”)

Packed 475 mm (18.7”) 210 mm (8.3”) 395 mm (15.6”) 5.5 kg (12 lbs)