Crown XTi 6000 XTI Series Power Amplifier
3000 Watts per channel into 2ohms
The XTi Series of Crown® amplifiers are professional tools designed and built for portable PA applications. The series includes four models which are similar except for output power: XTi 1000, 2000, 4000 and 6000. All are rugged and lightweight, and offer unmatched value in their class. XTi-Series amplifiers feature an LCD screen with speaker presets for crossover frequencies, EQ, limiting, delay, and a sub harmonic synthesizer. Other features include a switch mode universal power supply, useful function indicators, proportional-speed fan-assisted cooling, XLR inputs, Speakon® and binding- post outputs, short-circuit protection and more. With their powerful, reliable performance, XTi-Series amps easily handle 2-ohm loads and are capable of chest-thumping lows. Plus, your investment in an XTi-Series amplifier is backed by Crown's Three-Year, No-Fault, Fully Transferable Warranty.
Specifications - Crown XTi 6000 XTI Series Power Amplifier
|
XTi6000
|
1Khz Power
|
|
2 ohm Stereo (per channel)
|
3000W*
|
|
4 ohm Stereo (per channel)
|
2100W
|
|
8 ohm Stereo (per channel)
|
1200W
|
|
4 ohm Bridge-Mono
|
6000W
|
|
8 ohm Bridge-Mono
|
4200W
|
|
With 0.5% THD.
|
|
|
*With 1% THD.
|
|
Crown XTi 6000 XTI Series Power Amplifier
Output Power: Voltage Gain at 1kHz: XTi 1000: 30.5 dB XTi 2000: 32.9 dB XTi 4000: 34.2 dB XTi 6000: 37.1 dB
Frequency Response: +0/-1 dB from 20 Hz to 20 kHz at 1 watt into 4 ohms.
Load Impedance: Safe with all types of loads. Rated for 2 to 8 ohms in Stereo mode, 4 to 16 ohms in Bridge-Mono mode. The XTi 1000 A1 (100V version) is rated for 4 to 8 ohms Stereo, 8 to 16 ohms Bridge Mono.
Sensitivity: 1.4V
Signal to Noise Ratio (below rated 1 kHz power at 8 ohms): XTi 1K, 2K, 4K: 100 dB (A weighted). XTi 6K: 103 dB (A weighted).
Damping Factor: Better than 500 from 20 Hz to 400 Hz.
Crosstalk: > 70 dB below rated power, 20 Hz to 1 kHz.
Input Stage: Input is electronically balanced and employs precision 1% resistors.
Input Impedance (nominal): 20 k ohms, balanced; 10 k ohms, unbalanced.
Maximum Input Signal: +22 dBu typical.
DSP Section Input EQ: 6 parametric filters per channel with adjustable Q, ±15 dB boost/cut. Also adjustable high and low shelving filters. This 8-fi lter EQ section can be bypassed.
Crossover Filters: High pass and low pass per channel. Butterworth 6/12/18/24 dB per octave. Linkwitz-Riley 24/48 dB per octave. Also includes ±15 dB band pass gain and polarity control.
Delay: For signal alignment of driver; 50 mS total delay.
Sub-harmonic Synthesizer: Takes the low frequency content of the input signal and "synthesizes" a new signal that is the same as the input signal but one octave lower. The new synthesized signal is then mixed with the original signal to create the effect.
Output Limiter: Prevents clipping.
Presets: 20 presets, 19 of which are user-definable.
Front Panel Controls and Indicators Level: Detented rotary level control, one per channel.
Power Switch: On/off switch applies AC power to the amplifier.
Sel/Prev/Next Buttons: Three buttons near the LCD screen are used to access menu items and front panel lockout.
LCD Screen: Backlit liquid crystal display shows speaker presets.
Signal Indicator: Green LED, one per channel, illuminates when a very low-level signal is present at input. May be used for troubleshooting cable runs.
-10 Indicator: Green LED fl ashes when output signal exceeds -10 dB below clip.
-20 Indicator: Green LED flashes when output signal level exceeds -20 dB below clip.
Ready Indicator: Green LED, one per channel, illuminates when the amplifier is ready to produce audio.
Clip Indicator: Red LED, one per channel, turns on at the threshold of audible distortion.
Temp Indicator: Red LED, one per channel, illuminates under excessive temperature conditions.
Power Indicator: Blue LED illuminates when the amplifier has been turned on and has power.
Rear Panel Controls and Connectors AC Line Connector: XTi 1K, 2K, 4K: NEMA 5-15P (15A). XTi 6K: NEMA 6-20P (20A) IEC C20 (20A)
Input Connector: XLR, one per channel.
Link/Out Connector: Loop-thru signal from input connector for linking to another amplifier, one per channel.
Output Connectors: Two Neutrik® Speakon® NL4MP (mates with NL4FC) output connectors. Channel-1 Speakon® is wired with Ch. 1 and Ch. 2 outputs for use with optional single 4-conductor cable. Two binding post outputs(in parallel with Speakon® connectors).
HiQnet USB Connector: Type B, connects to a HiQnet network.
Protection XTi-Series amplifiers are protected against shorted, open or mismatched loads; overloaded power supplies; excessive temperature; chain destruction phenomena; excessive output current, input overload damage; and high-frequency blowups. They also protect loudspeakers from input/output DC, large or dangerous DC offsets and turn-on/turn-off transients.
Construction Chassis: Steel.
Cooling: Proportional speed fan with front-to rear air flow.
Dimensions: EIA Standard 19-in. rack mount width (EIA RS-310-B), 3.5 in. (8.9 cm) high and 12.25 in. (31.11 cm) deep behind mounting surface. XTi 6000 is 16.2 in. (41.15 cm) deep.
Net Weight: XTi 1K, 2K, 4K: 18.5 lb (8.4 kg). XTi 6K: 24.0 lb (10.9 kg).
Shipping Weight: XTi 1K, 2K, 4K: 21.5 lb (9.8 kg). XTi 6K: 30.0 lb (13.6 kg).
Optional Accessory: Rear rack-ear support for XTi 6000
Crown XTi 6000 XTI Series Power Amplifier
