The Nexo PS10 - LS600 R2 TD Controller MK3 is an advanced analogue processor that allows the PS10R2 Loudspeaker and optional LS600 Subwoofer to achieve exceptional performance from such compact packages. The PS10TD-R2 provides crossover, sensed amplifier control and system equalisation optimised for the PS10R2 and LS600. One PS10TD-R2 has two inputs and three outputs, L, R and summed sub out, minimising installation cost and complexity.

Like all NEXO processors, the PS10TD-R2 provides precision dynamic, voice coil temperature and diaphragm displacement protection through the use of selective Voltage Controlled Equalisers (VCEQs),
reducing levels only at frequencies when and where necessary.

KEY FEATURES

• Precision circuits engineered for the PS10-R2/LS600 systems permit increased sound pressure and operational reliability.
• Servo-controlled VCEQs provide precise dynamic control without spectral imbalance.
• Two inputs and three outputs enable a single PS10TD-R2 to manage multiple PS10-R2 and LS600 products.
• Comprehensive indicators and controls.

Nexo PS10 - LS600 R2 TD Controller MK3 PRODUCT FEATURES
Audio Inputs	Two L&R Audio inputs. Electronically balanced, 50KOhm. Two XLR-3F connectors.
Sense Inputs	Three Amplifier Sense Inputs (PS10-R2 L&R, LS600. 150 kOhm. 6 Pole Removable Strip Terminal. Passive Mode, PS15-R2 L&R, RS15. Active Mode, PS15-2 LF and HF, RS15.
Audio Outputs	Two L&R PS10-R2 audio outputs. Electronically balanced, 50 Ohm. Two XLR-3M. One mono (L+R) LS600 audio output. Electronically balanced, 50 Ohm. One XLR-3M.
Controls	Std/Max Protection Trimmer. Gain switch (back panel), 3 positions for Amps with Gain : 26 / 32 / 38 dB. Sub On switch & Sub Gain Control.
Indicators	Speaker Protect LEDs. Amp Sense & Peak LEDs.
Dimensions	1U 19" Rack. 190mm (7.5") Depth.
Weight	2.9kg (6.6 lbs) net.
SYSTEM SPECIFICATIONS PS10 TDCONTROLLER-R2
Input Level	+28dBm max into 600 Ohms.
Output Level	+20dBm Max. +19dBm Max on 1kOhm.
Noise	-88 dBm (22 Hz - 22 kHz, UnWeighted).
THD+N	< 0.03% Typ. 0.05 Max for +18dBm Output.
Power Supply	110/220 Volts (internal wiring), 50/60Hz. Earth-Lift (back panel).
SYSTEM OPERATION
Applicable Products	The PS10 TDController-R2 is precisely matched to the PS10-R2 & RS15 cabinets and includes sophisticated protection systems. Use of either product without a propery-connected Controller will result in poor sound quality and may damage the components
SHIPPING & ORDERING
Packaging	PS10 TDController-R2 is packaged as a single product.
Shipping Weight & Volume	4 kg (8.8 lbs) / 0.011 cubic metres.

As part of a policy of continual improvement, NEXO reserves the right to change specifications without notice. E&OE September 2009.

Architectural and Engineering Specifications
The 1RU Nexo PS10 - LS600 R2 TD Controller MK3 shall configure from a combination of two inputs and three outputs with each output providing crossover, parametric EQ, and mid-filter limiters for NEXO PS10 R2 products. The device shall have electronically balanced analogue inputs and outputs. All crossover, protection parameters, and EQ are factory optimized and not user-accessible. The controller must model loudspeaker temperature and displacement in real time. Protection shall be frequency selective and not allow PS10 R2 loudspeakers to exceed speaker-dependent thresholds. The controller shall have three inputs providing feedback from amplifier output to allow real-time, real voltage protection. Maximum input shall be 22dBu with CMRR 70dB@1kHz and THD+N of 0.05% (max) at+18dBm Output. A 3-position, rear panel gain control shall switch between 38/32/26dB amplificatory gain, and the Output Section shall respectively display +22/+16/+10dBm into a 600W load. LEDs shall indicate status for; Power ON (green), Amp Sense & Peak
(green/Red), Temperature & Displacement (yellow) and LS600 (VLF) displacement protection (also yellow). The chassis shall be constructed of steel with a black paint finish. Input power shall be 110-220VAC, 50-60Hz with a rear panel earth-lift. The 1RU device shall weigh 2.9kg (6.6lbs), with exterior dimensions of 483mm (19in) W, 44mm (1.75in) H and 190mm (7.5in) D. The controller shall be the NEXO PS10 TDController-R2 .

Nexo PS10 - LS600 R2 TD Controller MK3